| System Board Form Factor |
ATX 24.38 x 24.38 mm (9.6 x 9.6 inches) |
| Processor Socket |
Single LGA 1150 |
| CPU Bus Speed |
DMI |
| Chipset |
Intel® PCH C226 |
| Memory Expansion Slots |
4 DDR3 memory slots |
| Memory Type Supported |
DDR3, UDIMM (Unbuffered), ECC& non-ECC |
| Memory Modes |
Non-Interleaved for single channel. Interleaved when both channels are populated. |
| Memory Speed Supported |
1600MHz DDR3 |
| Memory Protection |
ECC available on data |
| Maximum Memory |
32GB |
| Memory Configuration (Supported) |
4GB and 8GB non-ECC/ 2GB, 4GB and 8GB ECC unbuffered DIMMs are supported. |
| ECC and non-ECC memory DIMMs cannot be mixed on the same system. |
| NOTE: * Maximum memory capacities assume 64-bit operating systems, such as Genuine Windows® 7 Professional 64-Bit or Red Hat Linux 64-bit. 32-bit Windows Operating Systems support up to 4 GB. |
| PCI Express Connectors |
1 PCI Express Gen3 x16 LP slot (x16 electrical/x16 mechanical) |
| 1 PCI Express Gen2 x16 LP slot (x4 electrical/x16 mechanical) |
| 1 PCI Express Gen2 x1 LP slot (x1 electrical/x4 mechanical) |
| 1 PCI Express Gen2 x1 LP slots (x1 electrical/x1 mechanical) |
| |
| NOTE: LP = Low Profile |
| |
| NOTE: In the PCIe Gen3 slot (x16 electrical/x16 mechanical) slot, if it is not being used for a graphics card, only cards certified as After Market Options for this platform are supported. |
| |
| Supported Drive Interfaces |
SATA |
Integrated (5) Serial ATA interfaces (6Gb/s SATA). One port can optionally be used for eSATA. |
| RAID 0 and 1 supported. Factory integrated RAID is Microsoft Windows only. |
| Serial Attached SCSI |
None |
| Integrated RAID |
NOTE: Requires identical hard drives (speeds, capacity, interface) |
| Integrated Graphics |
Integrated Intel HD Graphics 4600 (on Core i5/i7-4xxx processors); Integrated Intel HD Graphics P4600 (on Intel Xeon E3-12x5v3 processors). |
| |
| Based on Unified Memory Architecture (UMA)- A region of system memory is reserved and dedicated to the graphics display. |
| Support for Microsoft DirectX 11, OpenGL 4.0 and OpenCL 1.2 on Intel HD Graphics P4600; |
| 3 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP outputs. Max. resolution supported: 3840x2160 @60Hz |
| Network Controller |
Integrated Ethernet PHY Connection I217LM. Management capabilities: WOL, PXE 2.1 and AMT 9.0 |
| External SATA (eSATA) |
1 port eSATA capable with optional eSATA After-Market Option cable kit. |
| IDE connector |
No |
| Floppy connector |
No |
| Serial |
1 rear port |
| 2nd Serial |
Yes- requires optional Serial Port Adapter Kit |
| Parallel |
1 internal header (optional Parallel Port Adapter required) |
| CD-ROM input (Audio) |
No |
| AUX input (Audio) |
No |
| IEEE 1394 Connector(s) |
Rear |
2 IEEE 1394b (requires optional PCIe 1394b card) |
| Internal |
No |
| USB Connector(s) |
Front |
2 USB 3.0, 2 USB 2.0 |
| Rear |
2 USB 3.0, 4 USB 2.0 |
| Internal |
1 USB 3.0, 2 USB 2.0 |
| HD Integrated Audio |
Yes |
| Flash ROM |
Yes, 16MB |
| Chassis Fan Header |
Not applicable |
| Front Control Panel/Speaker Header |
Yes |
| CMOS Battery Holder - Lithium |
Yes |
| Integrated Trusted Platform Module |
Integrated TPM 1.2. |
| Power Supply Headers |
Yes |
| Power Switch, Power LED & Hard Drive LED Header |
Yes |
| Clear Password Jumper |
Yes |
| Keyboard/Mouse |
USB or PS/2 |
